Home > Support > Knowledge Base > Wireless > How to setup UTT WLAN Controller in Bypass Mode -- Multi SSID

How to setup UTT WLAN Controller in Bypass Mode -- Multi SSID

WX1000 Work In Bypass Mode Configuration Steps -- Multi SSID

Introduction

This document describes WLAN Controller works in bypass mode configuration steps.

Prerequisites

Requirements

Create 4 new WLANs with four SSIDs, WLANs are mapped to VLANs.

Eg:

SSID 1: Sale IP Address:192.168.10.0/24 VLAN 10 ;

SSID 2: Support IP Address:192.168.20.0/24 VLAN 20;

SSID 3: Oversea IP Address:192.168.30.0/24 VLAN 30;

SSID 4: Customer IP Address:192.168.40.0/24 VLAN 40;

Components Used

UTT WLAN Controller: WX1000; Firmware Version: WX1000V1.9.3-140609;

UTT WLAN in-wall AP: WA1300N; Firmware Version: WA1300NV1.9.3-140514;

Background Information

Configure

Network Diagram

Configuration

Configuring System Mode. Go to Network > System Mode page, select Bypass Mode, next configure it, then click Save, as shown in Figure 2-1:

Note:It need to restart the device to take effect after switching mode.

Figure 2-1

Disable the DHCP Server. Go to Network > DHCP Server > DHCP Address Pool List, next click default, as shown in Figure 2-2, then disable Checkbox, click Save, as shown in Figure 2-3:

Figure 2-2

Figure 2-3

Create a new VLAN Interface. Go to Network > VLAN Interface > VLAN Interface List page, click Add, as shown in Figure 2-4, next configure it, then click Save, as shown in Figure 2-5:

Figure 2-4

Figure 2-5

Create a new DHCP Address Pool. Go to Network > DHCP Server > DHCP Address Pool List page, click Add, as shown in Figure 2-6, next configure it, then click Save,as shown in Figure 2-7:

Figure 2-6

Figure 2-7

Create a new WLAN. Go to AP Controller > WLANs > WLAN List page, click Add, as shown in Figure 2-8, next configure it, then click Save,as shown in Figure 2-9:

Figure 2-8

Figure 2-9

Then you finished the configuration of the WLAN‘sale’, next create WLANs ’Support,Oversea,Customer’ as same as creating WLAN ‘sale’, after configured that, go to Network > VLAN Interface > VLAN Interface List page, you’ll see the list of VLAN Interface (VIF 10,VIF 20,VIF 30,VIF 40),as shown in Figure 2-10:

Figure 2-10

Then go to Network > DHCP Server > DHCP Address Pool List page, you’ll see the list of DHCP Address Pool (vlan10,vlan20,vlan30,vlan40),as shown in Figure 2-11:

Figure 2-11

Then go to AP Controller > WLANs > WLAN List page, you’ll see the list of WLANs (Sale,Support,Oversea,Customer),as shown in Figure 2-12:

Figure 2-12

Join WLAN. Go to AP Controller > AP Management > AP List page, select one list, then input password(password is “admin” by default), click Admin, as shown in Figure 2-13, then click Join WLAN, as shown in Figure 2-14, then select the WLANs which you want to join, next click Join WLAN, as shown in Figure 2-15, after that, you will see “Joining WLAN Please Wait”, as shown in Figure 2-16:

Figure 2-13

Figure 2-14

Figure 2-15

Figure 2-16

So far ,you have finished your configuration, then go to AP Controller > AP Management > AP List page, you can see the SSID of WLANs which you have joined in the AP,as shown in Figure 2-17, then you can connect to the SSID to have a test.